GENERAL LIFE MITRA HT10 RF Digital Room Thermostat User Guide

1

2

RECEIVER  

BATTERY PLACEMENT  

ENGLISH  

1-Manual Operation Button:  

By disabling the Receiver, it enables you  

to use your boiler manually.  

2-Pairing Button:  

1

2

3

DIGITAL ROOM THERMOSTAT  

generallife.com.tr  

Allows to pair the Receiver with the  

Room Thermostat.  

SERIES:  

MITRA, ARUNA, CERES, GAIA, ILLONA, NORA, SENNA, THERMA  

3-Receiver LED Light  

4-Receiver Power Cable Input  

5-Boiler Connection Cable Input  

Remove the battery cover located on the back of your Room  

Thermostat. Insert 2 new AAA alkaline batteries into the battery  

housing with the correct battery direction and close the battery cover.  

Replacebothbatteriesatthesametime.  

HT10 RF/HT10S RF/HT11S RF USER MANUAL  

DIGITAL ROOM THERMOSTAT  

GENERAL SPECIFICATIONS  

4

5

WARNING!  

HT10 RF/HT10S RF/HT11S RF is a wireless room thermostat. The  

user can adjust the room temperature with the required temperature  

and get morecomfortable and economic heating.  

When the product is not used for a long period (more than 15 days),  

remove the batteries. Otherwise, malfunctions that may occur would  

be out of warranty.  

RECEIVER LED DESCRIPTIONS  

 PreciseTemperatureMeasurement  

WirelessConnection  

Steady Red  

Receiver has power but Receiver and  

Pleasethrow yourdead batteriesinto the wastebin for batteries.  

 ON/OFFControl  

SERIES:  

MITRA, ARUNA, CERES, GAIA,  

ILLONA, NORA, SENNA, THERMA  

Room Thermostat are not paired.  

Blinking Green  

Steady Green  

Waiting for pairing signal from Room Thermostat.  

RECEIVER PLACEMENT  

HT10 RF/HT10S RF/HT11S RF AND EQUIPMENTS  

Room Thermostat  

Holder  

Alkaline  

Battery  

Receiver and Room Thermostat are paired.  

Boiler is not operating.  

The important things to note for the Receiver  

placement is avoiding physical contact between  

the Receiver and boiler, and protecting it against  

materialssuch asliquid,dust etc.  

3 Short Orange  

Blinking  

Operate the boiler signal has reached to the  

Receiver.  

HT10 RF/HT10S RF/HT11S RF  

USER MANUALS  

Steady Orange  

Boiler is operating.  

3 Short Green  

Blinking  

Shut the boiler down signal has reached to the  

Receiver.  

The devices should be placed in order to minimize the damage to the  

received and transmitted signals by paying attention to the following  

points;  

Dowels and Screws  

Receiver  

Blinking Orange  

Boiler is operating in manual mode.  

Blinking Red  

Receiver did not get a signal from the  

Room Thermostat for 22 minutes or longer and  

boiler has shut down.  

 The devicesshould not be mounted on metalsurfaces.  

 The devices should not be installed close to electrical cables and  

electronic equipment such ascomputers and televisionunits.  

 The devices should not be installed near large metal structures or  

other building materials using fine metal meshes such as special  

glass or special concrete.  

TECHNICAL DATA  

Room Thermostat  

ROOM THERMOSTAT PLACEMENT  

Room Thermostat needs to be placed in the room which is used most  

frequently. For instance; living room or lounge. Placing the Room  

Thermostat in a spot that have air circulation like entrance of a room  

or side of window should be avoided. Also anywhere close to heating  

units such as radiator, stove and spots which get direct sun lights  

would not be suitable. Room Thermostat needs to be located above  

Dimensions ( H / L / W )  

Operating Current  

85.7mm / 85.7mm / 33.5mm  

3V DC (2 x AAA alkaline battery)  

0.1^oC  

 Distance between the Room Thermostat and the Receiver should  

not exceed 20metersor 2 floors.  

Temperature Measurement  

Accuracy  

 Receivermust be installed atleast50cmawayfrom the boiler.  

Operating Sensivity  

Operating Temperature Range  

Battery Life  

0.3^oC  

RECEIVER SETUP  

 First, shut down your boiler and your boiler's power source with all  

electricalcurrent (fuse,socketetc.)  

(5^oC) – (30^oC)  

1 Year (2 x AAA)  

(-10^oC) – (+50^oC)  

(-20^oC) – (+60^oC)  

the floor  

150 cm height. Few trials may be made to find the most  

Operating Temperature  

Storage Temperature  

convenientspot.  

 As shown in the connection diagram, connect one end of the boiler  

connection cable to the COM and the other to the NO input.of the  

Receiver.  

Receiver  

 Connect the other ends of the cable -which you connected to the  

Receiver- to room thermostat connection terminal as shown in your  

boiler's user manual.  

min.20 cm  

Dimensions  

90mm / 90mm / 25mm  

230V AC  

Operation Current  

Relay NO Switching Current  

7A (240VAC – Resistive load)  

10A (120VAC – Resistive load)  

(-20^oC) – (+60^oC)  

 You must first connect the Receiver power cable to the Receiver  

and then to thefuse to which theboiler is connected.  

 After completing the cable connection process,firstly turn on your  

fuse and then yourboiler.  

Storage Temperature  

ROOM THERMOSTAT  

 By pressing the Receiver's manual usage button for 2 seconds, you  

should see the Orange Light blinking on the Receiver. In this way,  

after making sure that the boiler is operating, press the same button  

again for 2 seconds and seethatthe Orange LEDturns off.  

 Set up the Room Thermostat to pair the Receiver with the Room  

Thermostat.  

Indicator LED  

Adjustment Knob  

RoomThermostatIndicator LED Descriptions  

If it blinks once  

Room Thermostat sends a close signal to the  

Receiver and the heating unit stops operating.  

Room Thermostat sends an open signal to  

the Receiver and the heating unit starts.  

generallife.com.tr  

If it blinks twice  

If it blinks three times Room Thermostat sends a pairing signal to  

the Receiver.  

1

2

3

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	GENERAL LIFE MITRA HT10 RF Digital Room Thermostat User Guide
Make	GENERAL LIFE
Language	English
Filetype	PDF (Download)
File size	2.04 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• GENERAL LIFE

GENERAL LIFE MITRA HT10 RF Digital Room Thermostat User Guide Overview

Summary of Contents

• Page 1: Receiver battery placement is essential for proper operation. The manual operation button allows for manual use of the boiler. The pairing button is used to connect the receiver with the room thermostat. Receiver LED light indicators provide information on power and connection status. The receiver should be placed away from the boiler and protected from liquids and dust. Room thermostat placement should avoid areas with direct sunlight or near heating units. The distance between the room thermostat and the receiver should not exceed 20 meters. Receiver setup requires shutting down the boiler and connecting cables correctly. The room thermostat should be set up to pair with the receiver for proper functionality. Indicator LED descriptions provide feedback on the status of the heating unit.
• Page 2: WARRANTY CERTIFICATE In case of detection of manufacturer-induced errors of devices and apparatus whose warranty period continues, the customer can request a replacement or repair at full expense by the manufacturer. If your boiler has on-off connections, your Room Thermostat is compatible. We recommend that the connection between your Receiver and your boiler should be made by professionally qualified persons. Malfunctions resulting from the use of devices and apparatus contrary to the matters stated in the User Manual are not covered by the warranty. The Room Thermostat measures the temperature of its environment every 5 seconds. The warranty period starts from the invoice date and is against manufacturing defects for 2 years. Devices and apparatus are delivered to the customer in working condition. The customer can make complaints and appeals to consumer courts or consumer arbitration committees. The warranty document must be kept by the customer during the warranty period. In case of malfunctioning, it is tested whether the malfunction is caused by a customer or manufacturer fault.