sinop TH1134ZB Smart Line Voltage Thermostat Installation Guide

1

2

YOUR TH1134ZB/HC THERMOSTAT  

TECHNICAL SPECIFICATIONS  

Operatlng voltage: 120 / 208 / 240 Vac, 60 Hz  

TH1134ZB/HC Thermostat  

Maximum load:  

16.7 A / 2000 W @ 120 Vac  

16.7 A / 4000 W @ 240 Vac  

Resistive load only.  

Full-color display  

Minimum load:  

1.25 A / 300 W @ 240 Vca  

1.25 A / 150 W @ 120 Vca  

Cooling setpoint range: 61°F to 86°F (16°C to 30°C)  

Heating setpoint range: 41°F to 86°F (5°C to 30°C)  

Display range: 32°F to 99°F (0°C to 50°C)  

Storage: -4°F to 122°F (-20°C to 50°C)  

Operation: 32°F to 122°F (0°C to 50°C)  

Resolution: 0.5°C ( 1°F)  

TH1134ZB/HC  

Installation Guide  

Touch-sensor  

buttons  

Smart Line Voltage Thermostat  

Protocol: Zigbee 3.0  

Frequency: 2.4 GHz  

Transmission power: +20 dBm  

Receiver sensitivity: -108 dBm  

Compatible with an electric heating system such as:  

• Baseboard heater [short cycle]  

• Convector [short cycle]  

Touch control  

• Fan-forced convector [long cycle)  

• Radiant ceiling heating  

• Ductless air conditioners and heat pumps  

units with the HP6000ZB series controller^*  

^* Scan the QR code to view the list  

of compatible devices or visit  

www.support.sinopetech.com/en/1.1.29.3/  

Warnings  

Special CO/ ALR solderless connectors must be used  

when connecting with aluminum conductors.  

The installation of this thermostat must be performed by a certified electrician  

and comply with the national and local electrical codes and regulations.  

INSTALL YOUR THERMOSTAT  

Use the connectors provided to connect the thermostat wires to the wires in the  

electrical box. Use the screws to secure the thermostat to the electrical box.  

3

Unlock and lift the  

thermostat cover.  

1

Make sure that the  

breakers for your  

heating system are  

off at the main  

2

electrical panel.  

Three-wire installation  

Electrical  

Make sure to firmly tighten the  

wire connectors for a secure  

connection. A loose connection  

can be a fire hazard.  

panel  

L2  

N/L1  

3/4"  

To install wire connectors,  

you must:  

White - Neutral/Line 1  

Insert the two wires into the wire nut so that their  

copper ends are parallel.  

1

Red - Load  

Black - Line 2  

2

3

Turn the wire connector clockwise until there is  

strong tension.  

Replace the cover  

and lock.  

Power up the thermostat.  

5

4

Pull on the threads to make sure they are secure,  

leaving no gaps between them. * If the threads  

seem to come loose, repeat the process.  

* Improperly installed electrical wires could burn the wire  

connectors.  

To control a ductless air conditioner and heat pump unit, you  

will need to install an HP6000ZB series controller.  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	sinop TH1134ZB Smart Line Voltage Thermostat Installation Guide
Make	sinop
Language	English
Filetype	PDF (Download)
File size	0.56 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• sinop

sinop TH1134ZB Smart Line Voltage Thermostat Installation Guide Overview

Summary of Contents

• Page 1: YOUR TH1134ZB/HC THERMOSTAT Technical specifications include operating voltage of 120 / 208 / 240 Vac, 60 Hz. Maximum load is 16.7 A / 2000 W @ 120 Vac and 16.7 A / 4000 W @ 240 Vac. Cooling setpoint range is 61°F to 86°F (16°C to 30°C) and heating setpoint range is 41°F to 86°F (5°C to 30°C). Display range is 32°F to 99°F (0°C to 50°C) with a resolution of 0.5°C (1°F). Installation guide emphasizes that installation must be performed by a certified electrician. Warnings state that special CO/ALR solderless connectors must be used with aluminum conductors. Ensure breakers for the heating system are off at the main electrical panel before installation. Use provided connectors to connect thermostat wires securely to the electrical box. Improperly installed electrical wires could burn the wire connectors. To control a ductless air conditioner and heat pump unit, an HP6000ZB series controller is required.
• Page 2: Add your thermostat to the GT130 gateway and Neviweb. Connect your thermostat to the network by pressing briefly and simultaneously on the buttons. Initiate the connectivity session by pressing the RF signal button on the GT130 gateway. If you do not have an account yet, download the Neviweb app for iOS or Android to create an account and add your device. Once the connection is complete, a connection confirmation will appear on the screen. To disconnect your thermostat from the GT130 gateway or a compatible Zigbee hub, press the button for 5 seconds. To customize the settings in the configuration menu, you must access the configuration menu. This equipment has been tested and found to comply with the limits for a Class B digital device. Sinopé Technologies Inc. warrants the components of their products against defects in material and workmanship for a 3-year period from the date of purchase. Neviweb® is a registered trademark of Sinopé Technologies Inc. in Canada and the United States.